Skip to content
Contact

Fluidzon / Spare parts

Schwab UP 182

Explore the drawing and original articles. Confirm the model and installation generation before selecting a replacement.

Schwab UP 182 model reference

Model reference

Schwab UP 182

14 listed components

Cistern documents
Authorized partner for Schwab service & spare parts

Explore the assembly.

Select a position on the drawing, or find your article below.

14 listed components
Explore flush plate designs & finishes →

Select a drawing position below, or open the drawing to zoom.

Schwab UP 182 manufacturer exploded parts diagram

Drawing positions

Schwab UP 182 / replacement articles

Every part, in view.

Check the article code, cistern generation and connection before ordering.

14 of 14 components

1
Holder
363802
2
Protection cover, cistern 182
235139
3
Gasket for flush pipe
352277
4
Flushing pipe elbow with att., L=300 mm
359793
5
Flush pipe elbow 300 x 70 mm, white, view 1 of 2
1 / 2
382059
6
Fill valve HDV G 3/8 brass
628458
7
Connecting tube without stop valve (from 02/2014)
628459
8
Holder, cistern 180, 182, 188
239889
9
Flush valve with gasket, cisterns 182, 188
228578
10
Flange gasket for flush valve
351517
11
Flush valve holder with O-ring
352281
12
Set holder and release lever
231613
13
Spare parts set, cistern 182, 188
359812N

Not marked on the drawing

14
Set fill valve 182, 188, 180, 189
675100

Not marked on the drawing

Flush plates & finishes

Schwab UP 182 / flush plates

Choose the design. Then the finish.

Match the plate mechanism and installation generation before ordering. Current availability and the correct generation are confirmed on enquiry.

GALA, Matt chrome, 227702

2. Finish

227702
  • Matt chrome
  • Plastic
  • start-stop
  • mechanical

GALA · Matt chrome

Dimensions
345 x 180 x 32 mm (published Length x Width x Height)
Material
Plastic
Operation
start-stop
Mechanism
mechanical
Actuation
front
EAN
3838912034625
Generation & required hardware

182.0400 since 1999; dual flush or start-stop. Fill-valve revision 02/2014 is not a plate change.

Existing A2 cover 235139, I2 bridge 239889, I6 bearing bracket 231613. Product fixing material supplied; legacy family assembly set 228582 is a spare, not a plate.

Exact plate mechanism must match; no manufacturer plate revision/cutover date found.

Enquire about this plate ↗
Cistern documents

Cistern drawings and documents

Troubleshooting: find the cause, match the part

Model support

Check the cause. Match the article.

These are inspection references from this model’s parts list, not a diagnosis or a guarantee that replacement is needed. Confirm the generation and drawing position.

Fill valve generation boundary

For installations from 1999–February 2014, Schwab’s conversion table maps the old 243292 fill valve to replacement set 675100. The later generation uses 628458; check the model drawing and connection before ordering. A loose valve is not automatically a substitute for the complete conversion set.

Confirm the existing thread, holder, tube and required fittings. Installations near the changeover date need the actual cistern label and mechanism checked.

Schwab conversion-table reference ↗

Water continues into the bowl

Check the outlet seal and valve seating, fill shut-off and plate adjustment before selecting a replacement.

Slow refill or valve noise

Check supply isolation, filter and fill valve condition. Match the connection thread and installation generation.

Button loose or not operating

Check the plate mechanism, rods and holders against the model drawing; plate design alone does not establish compatibility.

    Use the drawing and request identification before ordering.

    Technical support · UAE

    The right part starts with the right model.

    Send a photo of the cistern label, the valve or the old part, plus the year it was installed. We confirm the right article and availability.

    Prepare support enquiry Prefer email? [email protected]
    Identify my part